The Crios’s perfect airflow design allows users to experience the best vaping.

Power-up your favorite tanks for amazing clouds of big flavors!
The Crios’s perfect airflow design allows users to experience the best vaping.

Key Features/Specs:
Sleek, compact design
24mm diameter
4ml liquid capacity
Easy top-fill

Each Crios tank is packaged with X2 BVC 0.65Ω Coils, tested and rated at 35W-65W
Replacement coils available in 4-packs
Available in black, Silver.

The Crios tank delivers huge flavorful clouds at 55W with an upgraded, easy to top-fill, design.
Available in Europe with the Axiom 2ml TPD compliant tank and coil system.

  1. Will this tank work with my original Kroma?

  2. Love this tank but would have preferred a normal drip tip the base of the drip tip gets too hot and is a bit big for my lips .Is there a tip I can purchase that will help

    • Hi Kevin,

      The Crios should include a 510 drip tip adapter. You can use any drip tip of your choice, provided you use the adapter. You can find tons of drip tips online for purchase. Thanks!

  3. Hi where can I get replacement coils from

  4. Will an 810 drip tip fit the Crios tank? I love this tank but the tip is a litte too short for my taste. I have see a taller 810 tip,but don’t want to buy it if it won’t fit.

    • I have two 810’s that I use on my Big Baby Beast and they fit perfectly on the Crios tank. But, the drip tips that come with Innokin’s new RDA (I forget the name… iRoar something) don’t fit. I was under the impression they’re 810 but maybe not. But if you have Goon, BB, Kennedy, etc. 810s they should work fine on this tank.

  5. what is crops coil made of ,, ss, ti, no ect

  6. The Crios tank is amazing! I love it! Will you be releasing other colors? If you release 100 colors, I’ll get one of each 😁 Also, will you be releasing other coils for this tank? The 0.65 Ω coils are amazing, but how about SS for temp control? Thank you for this wonderful tank 👍

  7. Any other coils coming out?

  8. Can i order these tanks direct from Innokin?

  9. I need a replacement glass for crio tank

  10. What is the point of having a security code? What can I gain/access with it. Product is itazte vv 3.0

  11. Will this work in a t22e? If not is there any with a airflow slot that will? Thanks

    • Hi Alex,

      I would not recommend the Crios with the T22e. The T22 is designed to output roughly 14W of power to high ohm coils, thus I would only recommend using atomizers with high ohm coils on the T22.

  12. Can you use SS Temperature control on this tank? I’ve been doing it and I am not sure if I should stop.

    • Hi Glen,

      The Crios coils that come with the tank and our bundles are BVC Kanthal coils. In other words, do NOT use the Crios in SS TC mode, as you could risk burning your cotton or destroying your coils. Please use your Crios in wattage mode only. Thank you.

  13. Where can i get clear tank glass o-rings/gaskets & maybe proper name for them?

  14. Will this tank work with my disrupter

  15. Hi just wondering would this fit my itazte kroma as my tank is broke

  16. Hello, have the coils for the Crios been discontinued? I just ordered the Kroma-A with Crios but when I went to order replacement coils from they told me that they have been discontinued. If they are discontinued is there a replacement? If not I paid for a tank that I can not use after the initial coils that it comes with burns out.

  17. I have a Cool Fire IV can with coils and cotton can I use this instead Im tired of wetting the cotton all the time it seems to dry out quick.

    • Hey Tone,

      You can use the Crios with the CoolFire IV, but the maximum output of the mod is only acceptable for the Crios coils. You may find yourself wanting or needing more power for the Crios. However, it should still deliver a satisfying vape and provide an upgrade for you at 30-40W.

  18. Thank You Innokin Frank for answering all these questions your very knowledgeable.

  19. i just purchase a Innokin Kroma-A Starter Kit which came with the Crios tank. I can’t get the bottom of the glass tank to stay on. The glass tube will not stay securely on the base of the tank. if i attempt to fill the tank it will leak out of the bottom. The bottom part of the O ring is there but nothing screws on. Any help?

  20. Is it alright to run this tank on a lower watt setting? Around 20-25W?

  21. this tank leaks real bad and I’ve tried new washers that came with it and it still leaks real, real bad getting ejuice all over everything.

    • Hi Gloria,

      Please make sure all of the o-rings are fully pressed into place. Also, you might need to either replace your coil, or use a thicker e-liquid. During the winter, the drastic temperature changes from going outside and inside can also cause leaks, as the temperature changes the viscosity of your juice.

  22. Hi, I just purchased itaste kroma a / crios tank,

    what is the correct setting for coil type when 1st setting up ? Same, Ni,Ti,ss,or w ?

    is there a difference between wattage in tc and wattage in wattage mode ?

    what is a recommended temperature setting so as not to burn my lips ?

    is it correct that with the crios, tc mode isn’t even meant to be used ?

    a list of all recommended settings for a rookie would be appreciated

    • Hi Luke,

      Use W, wattage mode. The difference between wattage in TC and wattage in wattage mode is the temperature. In TC, the wattage determines how fast you reach your set temperature, then the wattage cuts off to maintain that temperature. In wattage mode, you will get all the heat of your wattage setting for as long as you hold down the button, which means it’s important to use the recommended wattage setting for kanthal or stainless steel coils.

      If you’re using TC coils, I recommend starting at 50W and 400F.

      The Crios is meant for wattage mode, yes. Please refer to the engravings on your coils for recommended wattage ranges. Thanks Luke!

  23. Are replacement glass sleeves–not sure what the part would be called–available for the Crios tank? The one supplied cracked when attempting to reattach after trying to stop a leak. I was able to use the supplied replacement with the kit, but this only gives one glass sleeve to go with for now.

  24. Hi. Trying to change the coil for the first time but I can’t get the bottom to unscrew

    • Hi Jennifer,

      Place your Crios in a freezer for a couple of minutes, then try to unscrew the bottom section. If you still can’t get it open, try wearing a pair of rubber latex gloves while turning. Hope this helps!

  25. Buying the innokin AMVS starter pen that comes with the crios tank and. 25 coils which are the only coils recommend to be used in this device. Problem is I can only find the .65 ohm coils and nowhere the .25 coils. Any ideas as to where they could be purchased as I would like to use them per the manufacturer?

  26. I purchased an Authentic verified Kroma-A with a Crios tank, the mod is great but the Crios tank is a dissapointment, it hasleaked from the day i got it and the machuning of the base threads and cap thread is very poor to the point where is almost has no thread and barely holds on. Im not getting any customer support and was refused a refund or exchange and told by the store that they cant even get a reply and there listed on your website. Now om out of pocket $110 for a system i cant even use or have used for more than 10 mins. Very dissapointing.

    • Hi Darren,

      I am sorry to hear about the trouble you’re having with your Crios. Rest assured that all we want is for you to be satisfied with your vaping experience. Please contact our support team via email at with proof of purchase and a brief description of the issue. They will work with you to have a replacement sent to you or a refund if necessary.

  27. Will this tank work with the mvp3.0 pro?

  28. Hi
    I use the cool fire ultra with its original iSub tank on a regular basis, I recently purchased the Riptide with the Crios tank with the Kal 0.25ohm coil. as the Riptide battery needed charging I tried using the cool fire ultra with the crios tank but the screen message came up check atomizer and it did not recognize the tank, I assumed one can use any tank on the cool fire ultra as long you match the coil material in the settings and wattage, it should have come up flashing and giving me the option to change, can I not use any tank on the cool fire besides the iSub tank it came with.
    Thanks for your help and advice

Leave a Reply

Your email address will not be published. Required fields are marked *

Show Buttons
Hide Buttons