EZ.WATT Kit
The EZ.WATT is amazing! It’s an unbeatable kit, premium quality and beautiful! It’s Easy to operate and Great to Vape.
General Details
Vape the best of both MTL & DTL with the compact Innokin EZ.WATT Vaporizer!
The EZ.WATT is amazing! It’s an unbeatable kit, premium quality and beautiful! It’s Easy to operate and Great to Vape.
Do you enjoy puffing on incredible flavors with just the right amount of nicotine? Attach and vape the Endura T20S Tank with a Prism S coil for an unbeatably flavorful MTL puffing experience.
Looking for an amazing deep direct lung hit? Swap on the SlipStream tank and select 30 or 35Watts for big clouds and huge intense flavors. The bestselling Slipstream tank features full airflow control, top fill and an advanced top-down coil swap system.
It’s easy for anyone to vape great! Simply hold down the select and power button to cycle through 3 optimized wattage levels and press the Select button to choose from Low or High. The bright three color LED clearly indicates the current wattage level (13 – 14 / 16 – 18 / 30 – 35).
Quality you can trust! The EZ.WATT has integrated safety protections and is backed by the Innokin 90 Day limited warranty.
Innokin EZ.WATT Starter Kit
The EZ.WATT is amazing! It’s an unbeatable kit, premium quality and beautiful! It’s Easy to operate and Great to Vape.
Do you enjoy puffing on incredible flavors with just the right amount of nicotine? Attach and vape the Endura T20S Tank with a Prism S coil for an unbeatably flavorful MTL puffing experience.
Looking for an amazing deep direct lung hit? Swap on the SlipStream tank and select 30 or 35Watts for big clouds and huge intense flavors. The bestselling Slipstream tank features full airflow control, top fill and an advanced top-down coil swap system.
It’s easy for anyone to vape great! Simply hold down the select and power button to cycle through 3 optimized wattage levels and press the Select button to choose from Low or High. The bright three color LED clearly indicates the current wattage level (13 – 14 / 16 – 18 / 30 – 35).
Quality you can trust! The EZ.WATT has integrated safety protections and is backed by the Innokin 90 Day limited warranty.
Innokin EZ.WATT Starter Kit
Operating Wattage: 13W-35W
Battery Capacity: REAL1500mAH
Maximum Output Current：13.5A
Maximum Output Voltage: 7.5V
Clearomizer Resistance: 0.2 Ohm (min.)
Charging: Micro USB DC 5V/1A
Contents
1x EZ.WATT Mod
1x Prism T20S Tank (0.8ohm)
1x Spare Prism S Coil (1.5 ohm)
1x Spare Drip Tip
1x Quick Start Guide
1x Micro USB Charging Cable
1x User Packet
Colors Available : Red&Black Crackle,Black,Gray,Blue,Red,Purple
User Manual
Comments
When will the EZ Watt be released? Which site will have it first?
Also, are there any differences between this version of the T20 tank and the version included with the original Endura T20?
Hi J,
Thanks for your interest in the EZ.WATT! I am unsure which site will have it in stock first, but I’d personally suggest MyVaporStore.com and MyFreedomSmokes.com.
The tank provided with the EZ.WATT kit has more airflow than the T20, and is designed to work well at wattage ranges slightly higher. Hope this helps.
Why my ez watt tank is leaking?
Hi Matt,
There’s a number of reasons why your T20-S is leaking.
1. O-rings. Make sure none are missing or severely damaged.
2. Defective coil. Sometimes, a fix as simple as swapping out the coil can stop a leak.
3. Overfilling or overpriming. If you overfill or prime your coil too much, it can cause leaks.
4. Too thin of ejuice. Use 50% VG or higher e-liquid for less leak chance.
Hello, My tank is leaking as well. I just bought yesterday. I charged it first, fill up with the oil, then i wait for 20 minutes. During the time I wait, all the oil have been leaked.
Have we have to use the O-rings in the box to put between the tank and the part where you screw ?
Hi can you wash the tanks when empty so you dont taste the previous juice eg say i had orange but now i want lemon i can still taste the orange thats why i ask if you can wash them to remove old juice may a stupid question
Hi Jane,
You can certainly wash out your tanks to help switch flavors. You might look into VG soaking or other methods to help remove the taste. Some flavors, like menthol, are really hard to remove after using them in a tank, so for stronger flavors I’d recommend buying a tank to solely use for that flavor. Thank you!
I would like to check your item EZ.Watt. i need 10 samples of EZ.Watt and 5 Pack of Coils . We are based in London Uk and we are wholesellers. Please give us the price ASAP.
Thanks
Ayaz
Hi Ayaz,
Please contact us with your request as soon as you can via email to sales@innokin.com. Thank you!
Hello,
Are T20 coils compatible with the new T20s?
Hi Alan,
I’d recommend only using T20-S coils with the T20-S. Thanks!
YOU CAN ALSO USE THE SLIPSTREAM TANK IF U WANT DIRECT TO LUNG VAPE
We have just got our first stock of the EZ Watt kit today and I have to say its about at perfect as you could possible get for a beginner. The thing is tiny! I believe the T18 is probably one of if not the best selling ecig in the world but I believe this might just become the new best seller. Thanks INNOKIN !
Hey Mark,
That’s awesome! We’re extremely happy to hear your thoughts on the EZ.WATT and I personally share the same feelings you have towards it. We hope it helps beginner vapers worldwide get an easy, satisfying experience. Thank you!
I would be very interested in reviewing this for new vapers attempting to switch from smoking.
Hey Michelle,
For reviewer applications, send us an email to info@innokin.com with some examples of your prior reviews. We’d love to see your work!
Guide says press 0 + PWR to “cycle” through wattage. How is that different from changing the wattage via 0? Also, is there a way to chk battery life without plugging it in?
Hey KAP,
In order to cycle through the 3 wattage settings, hold the wattage button at the button, then hold the fire button. Once you’re on your desired level, let go of both buttons. You can then press the wattage button to cycle between the high and low settings for the level you’ve selected, indicated by the brightness of the bottom LED.
When you press the fire button while it’s turned on, the color of the button indicates what level the battery is at. Green for high, yellow for medium, and red for low. If it’s blinking red, it needs to be charged as soon as possible.
Hope this helps you.
The extra coil with the starter kit wont fit into my tank why?
Hi Samuel,
Make sure the flat sections of the coil are properly lined up to the flat sections of the coil hole cut-out on the T20. If they are both properly lined up with each other, the coil should press right in.
Hi,
I bought this vape a few weeks ago and have just gone to change the coil for the first time and am having this same problem. I lined the flat cutout sections up perfectly and it still wouldn’t fit.
Going to take it to the shop i bought it from and see if they can assist/supply me with another coil that does fit.
The extra coil does look slightly wider than the one that was in it originally so may be something you should look at?
thanks
Hey Sammy,
Thanks for the heads up. The spare coil should be exactly the same shape and dimensions as the one that comes with the EZ.WATT. Please let me know what your shop says- ask for a spare pack of coils if possible.
Hello.
Does anyone know if it turns itself off on its own and if it does how long does it take?
Thanks 😉
Hey Daniel,
It does not turn off on its own, it goes into standby mode. To preserve battery, get into the habit of turning it off when not in use.
Hello
I have been using the EZ. WATT for 3 weeks now after having smoked 25+ cigarettes a day for 30 years !! I feel healthier and wealthier, and would recommend to anyone. Thanks guys, best wishes Mark.
Hey Mark,
That is fantastic news! We are very happy to hear that the EZ.WATT is helping you kick the habit! Congratulations to you and keep it up!
We have recently purchased these little jewels and are just loving them. We quit smoking almost 4 years ago (pack a day for over 57 years) using the pen style devices; we were always having to replace the coils after about 3-4 days of using 100% VG. We are using the EZWatt, .8 at the lowest wattage and are now are getting 2 weeks off of a single coil. Large quantities of vapor and satisfying flavor. They do tend to flood when first refilled but we are able to overcome that pretty easily until the excess is cleared. Working our way down to lower levels of nicotine will be easier using these devices. Thanks so much.
So glad we found these. Most of us are not experts on devices, but this device is so easy to use, reliable and sturdy, you can’t go wrong.
Hi Winnie,
That’s excellent to hear! Congratulations on 4 years without going back after 57 years of smoking, that’s an amazing accomplishment. You are the exact kind of vaper we made the EZ.WATT for
Thanks for your support and keep on vapin’!
Great work you guys are doing here to improve the life of smokers in general. Hats off to you guys ??
Hi Cardoso,
Thank you so much for the support! Innokin thrives off of improving the health of smokers and ex-smokers worldwide. Appreciate the kind words!
I just bought one of these, filled it up ready to use but it appears to leak from somewhere around the base of the tank or the threading. I cannot see a clear guide on here to show me where the O-rings should be on the fittings to check that one has not fallen off – any help?
Hi Alex,
There should be two primary large o-rings at the base and top of the tank. It’s also possible that your coil is causing the leak; swap it out and see if the leak subsides.
I agree it would be useful to have a diagram of where the o-rings go. I got my new innokin today and on assembling, the o-ring fell out. I put it where `I thought it went but now I have vape juice leaking all over the place
I just purchased the EZ Watt system – charged it for an hour and a half and can’t get the thing to work! I tried clicking 3 times to turn on but no luck! The light continually blinks RED when I try to put it back on the charger. I’m using the supplied cable and preinstalled coil. What the heck is going on? Did I get a defective device?
Hi Joe,
It sounds like your battery is DOA. Please return it to your vendor immediately for a replacement, or contact us for a warranty claim at support@innokin.com. Apologies for the inconvenience!
is this device regulated?
Is this an upgrade from the T20S?
Hi Lee,
Yes, the EZ.WATT is regulated. It has more settings than the T20S, so while not exactly an upgrade, it gives you more flexibility for your vape. Thanks!
Will the T20S tank be available separately or is there and equivalent that you would recommend?
Hi Joseph,
Give our Zenith tank a try! It’s a mouth to lung tank with topfill and adjustable airflow, as well as fantastic flavor! It’d work great with your EZ.WATT. Thanks!
Hi,
For how long should the EZ.WATT battery conected to a proper charger for a fully charge?
Thanks
Hi Fonseca,
I recommend about 2 to 3 hours on average. Thanks!
Hi guys!!!!!first and foremost,thank you for this amazing little bit of kit which has probably saved my life!! I been a real heavy smoker for probably 30 years.i needed to stop but I had the “fear”! Having visited my local vape shop (vapemeister Bangor co.down Northern Ireland) they highly recommended I try this! I deliberated for few weeks and finally treated myself! I have now been totally cigarette free for approx 12 weeks now and will never smoke again! I LOVE my ez watt!so easy to use and so versatile! Although I do have 2 queries,if I want to use the higher power do I need a slipstream drip tank for use with more powerful coil and can u supply one to me over here in northern Ireland?and also I prefer the drip tank with removable mouth piece but I foolishly cross threaded it one night in the dark,is it possible to get a replacement???? Apart from that I can honestly recommend this fantastic vape to the max! Thank you Innokin!!!!
Hey there Alan,
Congratulations on quitting!
For higher wattage, the Slipstream can work, but I would recommend the Crios or Axiom instead.
We sell replacement drip tips on http://www.innokinstore.com but currently only offer products to the United States. I would get in touch with your local vendor to see if they have any replacement drip tips available for you. Thanks for the love!
Hi Frank. I’m a new user trying to get as much info as I can into vaping. In reply to the advice you gave Alan on your web page you say – Looking for an amazing deep direct lung hit? Swap on the SlipStream tank and select 30 or 35Watts for big clouds and huge intense flavors. The bestselling Slipstream tank features full airflow control, top fill and an advanced top-down coil swap system. – But here you are giving different advice. What gives?
Hi Johnny,
The Slipstream tank can handle lung hits, but we have other atomizers that produce more vapor, and can handle higher wattages. The Crios is also a more recent atomizer which offers a better experience in my opinion. Full disclaimer, many of the suggestions and advice I provide here is based on my opinions and experience. Product information pages are also rarely updated, and some information can become outdated eventually.
Also I should add the packaging,instructions and accessories (coils,rubber rings,spare drip tank top were sooooo cool too! It is also very compact,discreet and light but even on lowest setting it throws out mega clouds of my fave flav!!!!
Hi guys!!! I would just like to thoroughly recommend the ez watt to anyone!thanks to this amazing bit of kit I am totally cig free for approx 12 weeks now,which is some achievement considering my near 30 year heavy smoking habit! I totally LOVE my ez watt! Everything about this product ouzes quality! Packaging, lightweight,discreet, powerful, adjustable,smooth,hassle free vaping and the battery lasts forever! I was recommended this by my local vape store in Bangor Co.Down and I am very happy! Do I need a slipstream drip tank for using more powerful coil? Thanks again Innokin!
Hey Alan,
Congratulations on being 12 weeks smoke-free and happy to hear you love your EZ.WATT! The EZ.WATT was designed to go hand-in-hand with the T20-S tank. If you want to experiment with other atomizers, make sure they operate at a wattage between 13 and 35 watts, and use kanthal coils.
Much love! Thanks for your support and keep it up!
I have recently purchased a EZ WATT & it has broken within a week. I emailed “support” and have not gotten a response. I will not be recommending or rebuying.
Hi Beth,
I am sorry to hear about your experience. Unfortunately, a few defective products will slip through the cracks in any mass produced product. Our support team should get back in touch with you soon. Try sending a followup email.
My daughter has an EZ.watt innokin design that has started to leak at the top of the spacer ring that attaches the coil to the battery. Is there a fix, she couldn’t see any ‘O’ rings in the spacer.
Hi R,
Make sure the coil is pressfit properly. If there are any gaps in the coil slot, it will cause a leak.
Replacing the coil could also help the issue.
Hi,
I am now on my third Ez Watt, and it has now died. The first one lasted about 6 days before it kept shutting off, and would not restart unless plugged in, if only for a few seconds. Then it would not charge at all. My local Vape shop replaced it at no charge, that one only lasted about 3 days before it did the same thing. My local shop replaced it again. The manager said I shouldn’t let it charge overnight, that is killing the battery. I found this hard to believe, but I only charged it for an hour or two at a time, kind of a pain. It seemed to work, until I feel asleep last night with it charging for 6 hours, and sure enough it is doing the same thing. I cant believe that you cannot leave this charging overnight. I purchased your MVP when it first came out, and I have left it charging for days on end, and it still works. Please tell me there is some other issue at work here.
Hi Dan,
You should never charge a vaporizer overnight. That is a fire hazard- this goes for any rechargeable product. In regards to your EZ.WATTs, I would replace the charger and charging cable you are using to charge them. They should not be malfunctioning like this, and for it to happen the exact same way for 3 of them straight leads me to believe it’s your charging method.
I am confused as to what I might be doing wrong. I use the supplied charging cable, and plug it in. Maybe I’m a bit daft, but how can I screw that up. Please let me know what I might be doing wrong. I really like this unit, and I want to make it work.
Thanks
Hi Dan,
Is the EZ.WATT not charging, or turning on? What is the issue you are experiencing? Please reply so that I can assist you further. Thank you.
Hello
I have a innokin Ez.Watt and it don’t charge. I put it in the charge and the light on but then it turns off and does not charge. Untill the moment it charge very well and today doesn’t work.
You could help? Thank you
Hi Filipa,
I recommend trying a different charging cable or charging adapter. If it still doesn’t begin charging, your device may be defective. If you purchased it within 90 days, contact the vendor you purchased it from for an exchange, or email us at support@innokin.com with proof of purchase and a description of the issue. I apologize for the inconvenience.
Hi support,
I got my ez.watt innokin from a vape shop and love it but the battery doesnt hold its charge, lasts about one evening of use then dies, twice its done this now
What you guys recommend,
Thanks.
Hi Robert,
How often are you vaping? One evening per charge could be just right if you are a heavy user.
I dont take one puff i take about 3-4 puffs on medium setting as i find it isnt strong enough or is it best to go on the high setting then i wont puff as much.
And how long should i charge the vape stick for
Hi Robert,
The higher wattage setting sounds like it’d suit you better.
Average charge time is around 2 to 3 hours.
Thanks!
I brought one of those a few days ago and would like to know how long should the battery last as mine only last 4 hours before needing to be charged.
Hi John,
It depends entirely on how often you vape and what wattage setting you’re on. The higher wattage, the faster the battery will drain. If you tend to chain vape, it will drain the battery quicker. I can’t give you an exact time period as it is all based on user to user usage, but 4 hours doesn’t sound out of the realm of possibility.
hi support,
can i get a bigger tank for this?
Hi Robert,
Any atomizer using a 510 connector and kanthal coils will work with the EZ.WATT, so long as it can properly utilize 35 watts of power or less. Thanks!
Can you please specify what tanks and coils will work best with the ez.watt
Thanks,
Rob
ref EZ WATT : When charging battery red light comes on. But how do you know when battery is fully charged? Does the red light turn green or does the device simply switch itself off?
Thanks.
Hey Bob,
Your battery indicator should turn green when it’s close to being fully charged. Red indicates low battery charge.
I purchased my EZ Watt from Nashville Vapor on Charlotte Pike in Nashville TN 11 days ago and am happy with the performance so far. The starter kit I purchased came with an extra coil with a resistance of 1.5 ohms versus the installed coil of 0.8 ohms. Wondering why the difference, and what are the pros and con of 0.8 versus 1.5. With the same wattage setting, 1 coil will have higher volts versus lower amps or lower volts versus higher amps. I was also a little confused about the spare o-rings and where they are installed and how to tell if they need to be replaced. I too wasn’t clear on how to tell if the battery is fully charged. I assumed a red to green light means charged, but I’m hearing you all say that green indicates nearly charged, or sufficiently charged. One last question, There are 3 wattage tiers, 13-14, 16-18, and 30-35. I was recommended 13-14 or 16-18. When is appropriate to use the 30-35.
Thanks for your thought on all this. Randall in Nashville.
Hi Randall,
Thanks for picking up an EZ.WATT! I’ll be happy to help answer your questions.
The difference in coil ohms leads to different vaping experiences. The lower ohm coil is capable of handling higher wattage loads without creating a burnt flavor. This means the coil produces more vapor, consumes more power, and can be vaped at higher wattages. With these coils, direct lung vaping is popular. The higher ohm coil is basically the opposite- it can only handle smaller wattage loads, produces less vapor, and consumes less power. Higher ohm coils are better suited to starter kits due to their low battery consumption and great performance of mouth to lung vaping.
In regards to the o-rings, none of them should need replacement so soon. Inspect them every so often to ensure that they are properly in place and not torn or ripped in any way. If they are, please replace them with the provided o-ring kit.
The 13-14 and 16-18 tiers are best suited for the 1.5ohm coils. The 30-35 tier would burn the 1.5ohm coil and be very unpleasant. The 30-35 watt tier however can be used with the .8ohm coil. It’s up to your preference to determine which coil and wattage tier you like best.
With most Innokin mods, the charging indicator LED should turn off once the device is fully charged. When it is still charging and shows green, that means it’s got a high charge, but not quite full.
Thanks for choosing Innokin and let me know if you need more help.
Also forget to ask, what is the maximum suggested charging rate. My computer puts out 0.5 amps and my wall charger 1.0 amps. Is one better than the other, i.e. slower with 0.5 or faster with 1.0. Thanks again, R.
Hi Randall,
Charging is faster with a higher amperage, so in this case the 1A charger will be faster than your computer. All of our mods come with charging voltage and amperage specifications in the manual or on the box, so please be sure to use the proper charging method when using Innokin products.
For your EZ.WATT, either of your charging methods will work.
hi,
im using the 0.8 ohm coil and it works fine on the 13-14/16-18 settings but when i turn it to the 30-35 watt setting after a few puffs i get a burning taste, any reason why, do i need to get a less resistant coil like a 0.5
thanks,
rob
Hi there,
We purchased the ez.watt today and think it’s great and will definitely help us on the road to quitting the cigs!!
However, my husband has mentioned (numerous times…!), that he finds there is quite a lot of resistance when he takes a ‘drag’ or a pull on it…. Is there anyway to rectify this problem, via adjustment or is a different vape reccomended?
Would really appreciate your opinion and recommendations on this one.
With kindest regards,
Laura
Hi Laura,
The EZ.WATT comes equipped with an Endura T20-S tank which is designed for tight drags. However, the EZ.WATT is capable of being used with tanks up to 35 watts. He can try the Crios, Zenith, or any of our iSub tank line, which would all be compatible with the EZ.WATT and are capable of looser drags and higher amounts of airflow. Thank you!
Thank you so much for getting back to me. Will this info on and hopefully he will then be in the right path?
Thanks again x
Hi there thanks for your EZ.WATT it’s perfect but I want ask how u know the battery it’s changed full
Hi Martin,
When the EZ.WATT is charging and the LED is green, the LED should turn off to indicate the battery is fully charged. If the LED doesn’t turn off but has been green for at least 30 mins while on the charger, it’s safe to assume your mod is fully charged and ready to go.
1.) Is 1.0A the maximum amperage charging rate? Can you charge at 1.25A or 1.5 or 2.0?
2.) Is a lower amp charging rate better for the battery, i.e.is 0.5A better (although slower) than1.0A? Thx
Hi Randall,
1. Yes, 1A is the maximum amperage charge rate.
2. No, it will just make it take longer to charge.
Thanks for your support!
hi think my device is good how ever seem to be using a lot more liquid even on the lowest setting no leaks and not changed my oils my old t20 tank lasted lot longer than my t20s for liquids even tried the 1.5 coils unless u use more for the first couple of days with a new coil
Hi Barry,
That’s quite odd to hear, as the low settings of the EZ.WATT are very close to the wattage output of the T20-S. Honestly not sure what could be causing this. Are you certain you’re using more e-liquid than you used to?
After one night of vaping with this the beautiful tatse has gone after one refill?
I have replaced the coil also but I am not getting the full blown flavour. What other thing s should I check?
Hi Cormac,
You could be experiencing flavor fatigue. Try swapping a different e-liquid flavor in and then back to the original liquid you used.
I was told I can use any liquids in this model and have been using 70/30 but it’s not gaping too well, should it only be 80/20?
Hi Suzanne,
Higher VG e-liquids tend to vape better with our tanks. I assume you’re using a T20-S, 70VG 30PG should be working well. Maybe try another coil?
Hey there,
I have 3 questions.
i have been using the EZ. Watt T20s for like 3 weeks already without any issues. Only today i started getting the liquid in my month while puffing. What could be causing this? its not so amusing.
and how do i know when it is time to change the coil?
and it stays in my trouser pocket. so depending on my position, it is sometimes in a standing position, for horizontal position and also might be in an upside down position. Could that be causing any problems?
to conclude. this product is great. I would seriously recommend this one. and it helped me to reduce from nearly a packet of cigarette a day to 1 cigarette a day.
Thank you
Hi Ratish,
1. Coil flooding can happen for a number of reasons. Temperature change, overpriming of coils, or your coil needs to be replaced.
2. When your coil starts tasting worse than normal, or you taste a “burnt” flavor, it’s time to replace the coil.
3. This is not an issue unless you get dirt or lint in your tank. Make sure your pockets are clean!
Thanks!
Hi, I purchased the EZ.Watt in December and it charged fine…I didn’t use it for a while as I have many other E-cigs that I use…When I decided to use it again it wouldn’t charge so I took it back to the store where I purchased it and they tried to charge it with their connector and it still did not charge…As it is 90 days they suggested I contact you…please advise can be done about this problem…thanks
Hi Jocelyn,
Please contact our support team at support@innokin.com. We offer a 90 day limited warranty against any manufacturer defects. Our lovely support team will guide you through the warranty process. Apologies for the issue!
Hi
I have problems with Ez Watt. It is recharged regularly (and the charging light turns on), but does not Power on anymore, and no lights are lit. i bought it two months ago.
Can you help me?
Thk.
Hi Elvio,
I suggest using a different charging method. It sounds to be like your charging method is not properly charging the EZ.WATT’s battery. If you are still having trouble after using a different charging method, please contact us at support@innokin.com for warranty service. Sorry for the trouble.
I purchased the EZ Watt a few months ago and loved it so much, I bought one for my wife. Unfortunately, she’s having some issues that I have not experienced and we haven’t been able to figure out why. The device seems to be turning off on its own. We thought it might be user error so we swapped for a day and the problem persisted. We stopped by the Avail Vapor where we purchased the device and, while they were very kind, they could only tell us to search the internet for updates to download. I haven’t found anything for this device and not sure what to do next other than replace it – which I’d rather not do if I don’t have to. Anyone else having this issue and know what to do?
Hey Zach,
We do not offer firmware upgrades or updates for the EZ.WATT. Here’s a few troubleshooting steps for you:
1. Ensure the 510 connector is clean.
2. Check for damage/dirt on the 510 pin on both the tank and the mod.
3. Make sure the device is being properly charged with a certified CE charger. Do not charge the EZ.WATT with any charger with a rate above 5V/1A.
If it’s still acting up, contact our support at support@innokin.com via email for further assistance. Hope this helps!
Hi there,
I have been using this device for 3 weeks now and it is fantastic, have had a bit of leaking nearly every time i have refilled the Tank but not too much and only at first. I am going to be replacing the coil today and have seen online that a number of people have different ideas with regards to priming a new coil, i was told at the shop that i bought the device from never to put the liquid into the centre only to put it around the side, a few drops into each hole around the side of the coil and then do some unpowered puffs, fill the tank and wait for five minutes. Is there a wrong way to do it?
Hi Peter,
Your shop offered very sound advice, I would do exactly as they said. Directly priming a coil from the top is not technically a bad thing to do but when done improperly can flood your coil and cause leaks, so I recommend just priming the side juice intake ports. Thank you!
Hello! my problem is that the liquid flows from the tank. I’m afraid it’s going to be in the battery (it’s just been on its side). what would be the solution to this problem?
Hi Mantuli,
Replace your coil if you are having leaking issues with your T20-S atomizer. Also, make sure to use a thick enough e-liquid (we recommend no lower than 50% VG in the T20-S). Thanks!
Hello Innokin Frank!
Thank you the quick answer! This is my fault, because the liquid flow on the coil ?. But this vape is the BEST!!!! ??? Thank you innokin this little miracle ☺
Hi!
what happens if a prism t20s tank is used with isub coil?
Or the slipstream coil is work with that tank?
I just got my ez kit and the syrup leaks out. I’ve tried disassembling and putting it back together but it’s still leaking straight away. Is there anything you can recommend or is there a way I can have it replaced if it’s faulty?
Hi Chantel,
Based on your description, it sounds like there’s a missing o-ring or gasket in your T20-S tank. If you purchased the full kit, you should have a bag of spare o-rings and gaskets in your packaging somewhere. There should be thick o-rings that sit in the bottom and on the top of the glass section within the inside of the tank, as well as a small o-ring around the coil. Make sure they are all properly installed and you should no longer have leaking issues.
If you are still having leaking issues afterwards, contact our support at support@innokin.com and ask to file a warranty claim for a replacement. They will be able to assist you further. Apologies for the inconvenience!
i have been using the t20s with the 0.8 ohm coil at 30w (without problems) and love the flavour it give’s is running it at that wattage a problem?
thank you.
Hi Justin,
The coil is likely going to last less long as usual, but if you’re not burning your cotton, it should be fine to run it at 30w. Thanks for supporting Innokin!
What are the dimensions of the EZ Watt?
I used to use the aspire pockex but let me tell you this little jem is amazing its a great little device and satisfy all my need but quick question is it ok to use the 0.8ohm coil on 13-14 watts or do i have to stick to 16-18
thanks, John
Hey John,
Use whatever wattage range you find most comfortable!
Help!!… What does it mean when the on/off button keeps flashing green please? Not able to vape
Hi Leigh-ann,
Looks like it’s time to replace the coil. Replace the coil, make sure the device is charged, and power cycle it. It should work properly afterwards. Thanks!
Hi, I’m totally new to this and have been using the ez watt for nearly a week now after 25yrs of smoking….. It’s going well! Just wondering if you get any warning that your battery is running low?
Hi Michael,
The LED indicator should flash red when the battery is low. When the battery is at high charge, the LED indicator will be white. Glad to hear you’ve made the switch! Good luck and appreciate the support.
Hi.
I’m really interested in the red and black crackle design, but I’m a bit confused as to which one I’d get as it appears there are two different crackle designs from what I’ve seen.
The first one seems to have more of a red crackle pattern such as this: https://www.elementvape.com/media/catalog/product/cache/1/image/1800x/040ec09b1e35df139433887a97daa66f/i/n/innokin_ez.watt_35w_starter_kit_tank.jpg
But your store site has this pattern where it’s more black: https://www.innokin.com/images/2017/09/ez.watt-5-590×393.jpg
Is there any difference? Or is one pattern newer/older than the other?
Thanks.
Hi Taylor,
Before you purchase a crackle pattern EZ.WATT, please check with the vendor specifically to see which version they have in stock and are shipping out. I believe the pattern shown on elementvape is the older pattern. I hope this helps
I ha’ve this one and recently, after using it the red light comes on. The the green, yellow and red lights flash and the red light goes away. While using it, the red light stays on (not while I have the button down, after I release it and before I press it). What causes this? How can it be fixed?
Hi Tiffany,
This sounds like a coil short. Replace the coil in your atomizer and see if it fixes the issue.
Hi support,
I’ve had my EZ watt for about 6/7 months and its fantastic. It has just developed a problem tonight. when i go to press the button to vape it doesn’t vape. the green light comes on as usual but stays on for 5 seconds after i release the button. also the small blue button at the bottom only flashes for a split second. It is turning on and off ok and seems to be charging as well. any ideas. thanks Martin
Hey Martin,
Sounds like a short. Replace your coil and see if the issue persists. Hope this helps.
Hi. I have recently bought the Ez watt and I love it although I have had a few leaking issues. I went to my local vape shop to buy a pack of replacement coils and was sold a pack of T20 coils, the guy said that these were the correct ones. Is this right or should I take them back?
Hi Dirk,
The EZ.WATT comes with the T20-S tank, and thus requires T20-S coils. The T20 and T20-S coils are different, and they are not cross compatible. Make sure they are T20-S coils or you will have to get them exchanged by your shop for the right coils.
Hi my red led light now just stays on when it’s off an even on. When I vape it turns green but then strat back to red light. I’ve changed the coil but it still show red please help
Hi Tania,
Make sure your battery is charged! You might have something stuck behind the button. I recommend using a gentle amount of compressed air to clean the button.
I just bought a vape about a hour Adolfo and it will not turn on. Can you tell me if I’m doing something wrong or is my ez watt vape defective?
Hi Timberly,
Ensure the device is fully charged. It can be charged via the micro-usb port with a power adapter or through a USB2.0 port. The device can be turned on with three quick clicks of the fire button. If it remains unresponsive, it will have to be exchanged at the vendor you purchased it from, or you can contact us for direct support via email at support@innokin.com. Apologies for the inconvenience and hope this helps.
Hi, my unit charges fairly quickly but then loses charge rapidly with the green light staying illuminated slightly at all times. Can you please advise.
Hi Paul,
You might have an issue with your fire button. Make sure no dirt or dust is hidden behind the button! Try blowing it out with a compressed air canister. If that doesn’t help, please contact our support team at support@innokin.com as soon as possible. Thank you!
hello my power button is constantly red even when not in use and when i use it it goes green then straight back to red? could you tell me why this is please
Hi Jordan,
Try turning the mod off and leaving it off for a few minutes. Does the issue still persist? If so, put it on the charger and wait until the mod is fully charged. If the LED still stays on, there may be a chipset issue, in which case you’ll have to contact our support team for a warranty claim if it was purchased within 90 days. You can reach us at support@innokin.com at your earliest convenience. Thank you and sorry for the trouble!
Where can I buy spare o rings from for the EZ Watt?
Hi Steve,
We offer many o-ring and parts kits on our official webstore, http://www.innokinstore.com. Hope you find what you’re looking for! If you need further assistance let me know. Thank you.
What about in the U.K.?
Will the Innokin Plex tank work with the EZ Watt?
Hi Saf,
No, the EZ.WATT does not provide enough power output to sufficiently power the Plex tank. Please do not use a Plex on the EZ.WATT.
My EZ.WATT has been great. Helped me smoke significantly less, but I have two problems within the first week.
The 510 threading on my vape has been leaking from the two holes in it. It had only started today and I’m not sure why.
There is a burning taste when vaping, and the liquid sometimes shoots out from the Drip Tip on top. I’ve tried replacing the coil, but that didn’t help.
Hey Marc,
It sounds like your tank is struggling to maintain a proper vacuum. Make sure all the o-rings are properly in place and undamaged. The EZ.WATT kit should have come with a spare o-ring kit. If one seems damaged or missing, please replace it.
I am looking for a larger tank and coils for my EZ Watt that would be best for mouth to lung vaping- any suggestions?
Hey Ryan,
Maybe give the Zenith a try. It’s not too much bigger than the T20-S, but it offers a great mouth to lung experience and should be compatible with the wattage output that the EZ.WATT offers. Hope this helps!
Hello
I have tried sending you a message via your website but I got an auto response saying it was not delivered for some bizarre reason, so here goes again!
As mentioned in my previous message, I would like to contribute an article to your blog on UK and EU vape laws. I used to work for a vape shop in London some time ago and I have picked up quite some knowledge on the TPD laws. I have also talked about the vape laws in some other European countries (the ones I am knowledgeable about at least).
I have saved the article in a word document on my G-Drive which you can access from here:
https://drive.google.com/drive/folders/1ETR42QSnvwBUhy4kbfz6twx0pZUS1hTN?usp=sharing
Whilst writing this article, I contacted a couple of websites to get some references to substantiate the article and back up some claims with personal anecdotes. I am sorry but I did not have the time to get any images so it would be great if you could add some that you deem appropriate.
Just in case you want to add a bio to the article, I have cobbled together this blurb about myself.
Tony is a vaping enthusiast who is currently vaping Blueberry Donut by Marina Vape. Tony used to work for a vape shop based in Shoreditch, London. He enjoys attending vape expos and spending quality time with his wife Melinda, three kids and two dogs in the rural settings of Kent.
I will write up a few more articles as and when I get some downtime at work – it is crazy busy after the festive season!
Have an awesome day!
Regards
Tony
can I use my phone charger to charge my EZ WATT? The kit only came with the USB lead in the box and im not sure if am to only charge via USB or can I plug the USB cable into a plug adapter
Hi Ro,
We do not advise using car chargers to charge Innokin products. Car chargers frequently have over-amperage issues and cause damage the charging circuit or batteries of our devices. Please only use a 5V/1A wall charger or USB2 port. Thanks!
Hi
Please, how many ml in the original tank ? Thank’s
Hi Margaux,
The EZ.WATT is bundled with the T20-S, which has a 2mL juice capacity. Thank you!
Hello,
I just changed the coil for the first time and then re-filled the tank. I left it 5 minutes to settle as suggested. When I started vaping it tasted horrible so I pressed the button on and off a few times to “Prime it” (not in my mouth) and then I tried again properly but without inhaling it because I could still taste the horrible taste.
Been doing this for a while now and it’s still not improving? Is this normal? Any suggestions?
Thank you
Emma
Hi Emma,
“Priming” the coil is not firing it- it’s the process of putting drops of juice inside the cotton juice ports and chimney section of the tank before you insert it into the tank. Then, after it’s primed, you allow the coil to sit inside a filled tank for at least 5 minutes before you first vape. The coil you’re using now is likely burnt and will forever have that horrible taste, so I suggest discarding it and starting the process over, this time priming the coil and allowing it to soak up juice before first vaping. Do not allow the coil to vaporize e-liquid without you puffing on it, as the lack of cooling from the air intake of your inhale will cause the coil to overheat and potentially burn, causing poor flavor.
Hope this helps!
Hi,
Just wondering if i can buy a battery alone for this one my tank is still mint, thanks.
Jelly
Hi Jelly,
You are looking for an EZ.WATT express kit. Check out your local Innokin dealer, or refer to this list to find one: https://www.innokin.com/authorized-innokin-distributor/
You may also be able to find what you’re looking for on http://www.innokinstore.com. Thank you!
The ez.watt is epic. So simple to use and to understand.
I have the older crackle effect, what is the difference between the new and the old one?
Also if want more flavour and vapour what would be the best set up?
Thanks
B
Hey B,
Thanks for the kind words! Glad you’ve been enjoying your EZ.WATT. There’s only a visual difference between the two crackle colorways.
A similar all-in-one easy to use kit like the EZ.WATT but offers much more vapor and intense flavor would be the recently released Plexar. Give it a look! Thanks for your support and happy vaping.
Fantastic piece of kit! Stands up to the rigors of daily life. Very Good battery life and easy to use. The only actual problem i encountered was the drip tips (both that came with it) eventually came loose and had to be replaced. I didnt over tighten or anything so dont know how that happened. The only design change id make is a battery level indicator more visible when vaping. 4.5 outta 5
Hey Scott,
Thanks for the kind words and mini review! The drip tip issue may have been from damaged o-rings. There are two o-rings at the base of the drip tips that may have gotten loose or damaged somehow. You can always order spares from http://www.innokinstore.com.
Noted on the battery indicator level! Thanks again for supporting Innokin and happy vaping!
Two week ago I bought the Innokin EZ.watt & it’s great. The thing is I tried using it this morning but found I couldn’t charge it. ALL the lights are on ALL the time. pressing buttons does nothing, Plugging in does nothing & neither does replacing the coil. woops.
Hi Stuart,
It sounds like there is an issue internally with the chip, and may need a warranty replacement. Luckily, we offer a 90 day limited warranty service to cover these issues. Please contact our warranty support at support@innokin.com via email to open a warranty claim. Very sorry to hear about the trouble you’re experiencing, but we will get to the bottom of the issue
Hi I just wanted to write a quick review I bought the ez watt for me and my mum, I have smoked for 31 years my mum for 53 years. We are now approaching 5 month without cigarettes. I have gone from 20mg nic salts down to 6mg nicotine in that time my mum is down to 12mg. We both use the 1.5omh coils and we both use direct to lung without any issue at all. Battery lasts me all day with out any problem. Only issues I have is tank must be empty before changing coils and I always end up with e liquid on my fingers from the screw cap. I am looking to upgrade my tank to either the zenith or the zlide tank.
Hi Robin,
Thanks for writing and sharing your review! We are extremely happy to hear about you and your mother’s success of quitting cigarettes! Congratulations to you both. Glad to hear you’ve been enjoying the EZ.WATT kits as well! In order to avoid a mess when changing the coil, we recommend unscrewing the top fill cap, spilling the remaining juice out, and then changing the coil. Thanks and happy vaping!
Hi guys
I have had a T20s now for a year and very happy with it has helped me a lot giving up smoking, The only problem I have is I have gone through 3 top caps as I keep cross threading them, Do you sell spares please, The shop I bought my gear from says they don’t sell spares and I would have to buy a tank but I don’t need a new tank just a cap
Hey Paul,
We offer spares on http://www.innokinstore.com. Thank you!
The EZ-WATT is by far my favorite of the dozen or so devices I’ve purchased, some of which were considerably more expensive. Although the airflow isn’t adjustable, the draw is perfect for a former cigarette smoker such as myself. The 16 W setting allows me to take slow drags, as one would from a cigarette, without overheating. And the aesthetic appeal of the black crackle is unparalleled.
Just one question: how do I obtain a replacement for the internal battery, and how do I install it? Is it as simple as unscrewing the bottom plate and the battery falls out?
Hey Michael,
Glad to hear you’ve been enjoying your EZ.WATT! The mod is designed as an internal cell only device, and as such we do not offer replacement battery packs and do not recommend trying to replace it. The internal cell system is designed to keep costs low. You’ll have to purchase another EZ.WATT mod if your current battery is not holding a long enough charge.
Thanks for your support and happy vaping!
Can I buy a top cap as I’ve gone through 3 in a year, Been told by the shop that I would have to buy a tank aswell.
Hi Paul,
We offer a decent selection of replacement parts on our webstore, http://www.innokinstore.com. If you can’t find what you’re looking for there, then you’ll likely have to buy a replacement tank as your vendor mentioned. Hope this helps.
Igot the EZ.WATT Battery so the Battery for the Endura T20 S could be used as a back up battery
hey there I have the ezwatt and I keep getting vape juice in my mouth when I suck, tried new coil and worked for one refill and getting the same result now.
Hi Kieran,
This is a common issue typically referred to as flooding. A coil can flood for a number of reasons, but the most common is overfilling, or thin juice. Empty the tank, and fill it to about 50%. If that doesn’t help, try a thicker eliquid (one with higher VG percentage). If all else fails, replace the coil. Hope this helps!
I just bought this product and straight out the box if I turn it on it fires constantly until I turn it off again. Is there a fix for this or is the whole thing faulty?
Hi Jack,
So sorry to hear about the trouble you’re having with your new EZ.WATT. It sounds like a defect out of the box, which thankfully is fully covered under our 90 day limited manufacturer warranty. Return it to the store you purchased it from for an exchange, or contact us at your leisure at support@innokin.com to begin a warranty claim. So sorry again for the trouble.