iTaste MVP 20W

The iTaste MVP 20W is the newest in the line of bestselling Innokin Technology iTaste MVP vaporizers and features a wider range of Variable Voltage and Wattage, advanced safety features, a long lasting 2600mAh battery, ‘Vape while you charge’ technology and the MVP20W e cigarette can also be used to charge your mobile phone and other electronic devices.

Category:
General Details
iTaste MVP 20W:

Variable Voltage:
Voltage can be adjusted from 3.3 – 7.5 volts in .1 volt increments.
Variable Wattage:
Wattage can be adjusted from 6.0 – 20.0 Watts in .5 watts increments.
Battery Level Indicator:
The MVP20W e cigarette battery capacity is displayed via green, yellow and red LED.
Green = Almost fully Charged. When the MVP20W fully recharged the LED light will power off.
Yellow = Half Power.
Red = Low Power. Charge the MVP20W.
Large battery capacity:
The MVP20W has a built-in 2600 mAh polymer Li-Ion rechargeable battery.
ON/OFF battery switch:
Press the power button three times in rapid succession to turn on the MVP20W. When the MVP20W is powered on Hold down the button to activate the atomizer and vape. When the MVP20W is not in use, press the button three times in succession to power off the MVP20W Advanced Personal Vaporizer. Always power off the MVP20W Advanced Personal Vaporizer when it is not being used, or when it is going to be stored in a pocket, bag or purse.
Ohms meter:
Reads the resistance of your atomizer/cartomizer/clearomizer.
Puff Counter:
The integrated Puff counter will record the number of puffs you have taken. Either press “P “button or “U” button for 1 second to check the number of puffs. The Puff Counter will reset to 0 whenever the device is powered off.
SAFETY:
* 10 second Cutoff: If the activation button is held for longer than 10 seconds the MVP20W Advanced Personal Vaporizer will stop firing until the button is released and pressed again.
* Low Voltage Warning: The Red LED and Battery bar will continue blinking when the battery capacity is lower than 3.3V and the MVP20W Advanced Personal Vaporizer will power off automatically.
* Short Circuit/Atomizer Protection
Short Circuit/Atomizer Protection protects the MVP20W Advanced Personal Vaporizer against shorted atomizers and will stop the unit from functioning in unsafe conditions.
Over-Discharge Protection:  The MVP20W Advanced Personal Vaporizer monitors the battery voltage and will automatically power off when the battery is discharged.
* ‘Vape while charging’ Technology
The MVP20W is recharged with a Micro USB cable. When plugged into a power source the MVP20W can also be vaped and charged at the same time with Innokin Technology’s ‘Vape while you charge’ pass-through technology.
* Remembers last Voltage or Wattage setting
* When the MVP20W is turned off it will store the current voltage or wattage setting and it will retain the setting when the MVP20W is powered on.
* Built-in 3 digit display
* Digital display shows the Ohms meter, Voltage / Wattage setting and the number of Puffs taken since last time the battery was turned off.
* Portable power source for electronic products
* To charge your portable electronic device with the MVP20W – set the small pin switch on the bottom of the MVP20W to the ON position and connect a microUSB cable to the USB OUTPUT port (DC 5V, maximum output current 0.5A)To maximize the battery charge of your MVP20W e cigarette please ensure that the bottom switch is set to the Off position when you are not using the portable charger function.

Technical Info
  • Operating Voltage: 3.3V-7.5 V
  • Operating Wattage: 6.0W-.20W
  • Standby current: 100uA max
  • Maximum output Wattage: 20W
  • Maximum output Current:6A
  • Maximum output Voltage: 7.5V
  • Clearomizer Resistance: 1.0 Ohm (minimum)
  • Battery: Built-in 2600 mAh polymer Li-Ion rechargeable battery.
  • Charging: Micro USB DC5V/1000mA
  • OUTPUT port :DC5V /1000mA
Review Videos

 

 

 

Comments
8 Comments
  1. I have an innokin mvp 20w in my possession. what I don’t like about this is that I have an arctic tank with btdc. I use it on a sigelei 150w tc. the threads on the tank arent long enough to touch the heating well on the innokin.

    This should be a universal measurement. all tanks should be the same. my tank works with any other box out there in its league, why not this one?

    you guys market this box and include a pos tank with it, the iclear 30s, that quite honestly, cant even work at above 10w. if you put it above 10w, even 10.5w, it automatically burns.

    This is a good box (could be loads better. would be nice if it went to 40w instead of 20w. and if the threads were re-worked so that you could put ANY market tank on there instead of the POS stock ICLEAR30S with 1.5 ohm resistance coils. I use a 0.2 ohm sub tank in my sigelei 150w. how are you supposed to get any enjoyment out of this f***ing box???) but the tank included with it from the website is *$(#. There needs to be a list of tanks that WORK WITH THIS BOX.

    • Hi Matthew.

      The reason you cannot use your Artic with the MVP20W is because the ohm load is too low for the MVP20W. The MVP20W supports a minimum 1.0 Ohm resistance- please use atomizers above that resistance for the best experience.

      Thanks!

  2. Hi can you tell me what tanks and coils you need to use with the mvp 20 as i have one but want to upgrade it

    Thanks.

  3. i bought my new MVP 20W a week ago. the battery holds a charge for 7h only :(

  4. I have an mvp 20w and blinked red the other night and now won’t charge when I plugged it in, is the device dead? If so, how can this be fixed?

    • Hi there Shelby.

      How old is the device? Do you have any other chargers to test it with? Did it show any other odd behavior before blinking red?

      Hope I can help you solve the issue. Thanks.

Leave a Reply

Your email address will not be published. Required fields are marked *

Show Buttons
Facebook
Reddit
Pintrest
Instagram
Twitter
SEVIAUSA
Hide Buttons